Water-based wooden protector for the protection of wooden platforms. Good resistance to weathering, excellent blocking. Contains ultraviolet filters. Fast dry. Does not yellow.
Water-based satin wood protector for wooden floors Titanlux
24,50€VAT included
Water-based wooden protector for the protection of wooden platforms. Good resistance to weathering, excellent blocking. Contains ultraviolet filters. Fast dry. Does not yellow.
You might also like
Related Products ( 14 other products in the same category )
-40%
-30%
-40%
-30%
-40%
Description
Water-based wooden protector for the protection of wooden platforms. Good resistance to weathering, excellent blocking. Contains ultraviolet filters. Fast dry. Does not yellow.
Technical characteristics
- Nature: Alkyd Acrylic
- Color: Colorless
- Yield: 10-16 m2 / L
- Drying at 23ºC 60% RH (UNE 48301): 1 - 2 hours / dry touch: 15 - 30 minutes
- Repainting at 23ºC 60% RH (UNE 48283): 6 hours
- Application tools: Brush and Roller
- Cleaning of utensils and dilution: Water
How to use
General recommendations
Stir well in the container. Surfaces must be smooth (sanded), degreased, clean and dry. Apply in thin coats and sand lightly between coats. 2 The moisture content of wood should not exceed 12% in hard wood and 15% in softwood. The varnish has a milky appearance that disappears after a few minutes
Unprepared surfaces
Sand the wood in the grain direction, thoroughly clean, remove resins or resin secretions and kill sharp edges.
Old unvarnished wood: it is essential to completely remove the dry and gray surface by sanding or brushing thoroughly until the wood in good condition is exposed.
Indoors: apply 2 coats.
Outdoors: For better protection of the wood outdoors, apply Titanxyl Total Protection Ultra or Titanxyl Lasur Bottom Ultra, finishing with 2 or 3 coats of Lasur Decking Water Protector.
For restoration of interior wood with woodworm problems, apply a layer of Titanxyl Water-repellent, with mold problems, apply a layer of Titanxyl Total Protection Ultra or Titanxyl Lasur Ultra Fund.
In case you need a non-slip behavior, apply a layer of Lasur Anti-Slip Flooring Water Protector.
Resinous and tropical woods: can prevent drying. Thoroughly degrease with Aguarrás Mineral to remove the resin. Apply a first coat on a reduced surface and observe. If the resin exudation persists, consult the Technical Service, but finish with 2 - 3 layers of Lasur Platforms.
Maintenance of already painted surfaces in good condition
Wood treated with lasur: remove dust and apply Lasur Pallets Water Protector. Perform maintenance when you start to see bare wood, due to the Lasur's self-controlled wear.
Varnished wood: completely remove the existing layers with Paint Remover Plus TITAN and proceed as on unprepared surfaces.
Maintenance of already painted surfaces in poor condition
Remove completely and proceed as on unprepared surfaces.
22265
4 Items
Data sheet
- Kind of product:
- Finishing paint or final coat
- Degree of Brightness
- Satin
- Theoretical yield per hand (m2 / L):
- 12
- Number of recommended hands:
- two
- Sanding between layers
- It is not necessary
- Dry to Touch at 23ºC and 60% RH
- 15-30 min
- Time for repainting at 23ºC and 60% RH
- 2 - 4 h
- Diluent / Cleaning:
- Water
- Number of Components
- 1 component
- Type Application:
- With brush or roller
- Place of application
- Interior and Exterior
- Paint Wood
- Directly
- Paint Already Painted Surfaces
- A smooth sanding and painting directly
- Danger for transport:
- Innocuous, without restrictions
Specific References
- ean13
- 8414800423655
No customer questions for the moment.
Your Question has been successfully sent our team. Thanks for question!
Ask a question
hide form