High quality acrylic solvent for acrylic resin mixed with any solvent: bilayer paintings, rigging, primers, varnishes, etc. slow drying so it is ideal for workplaces where very hot or hot seasons like summer. It is also ideal for slow drying when incidents arise boiled or powdered dried in the air.
Solvents, Adhesives and Others
The Urki-Blend Spray presents a mixture of solvents to facilitate the integration of new and old paint in partial repairs and body repairs. The VOC content is less than 840 g / l (2004/42 / CE) IIB (E)
The CLEANER & POLISH spray has been specially designed to clean the surfaces of grease, insects and to protect against the accumulation of dirt. You can polish the chrome, aluminum and varnished surfaces. It protects against UV rays and lends the surface a lasting shine. It is waterproof and has silicone.
Special Agent developed to reduce the brightness of paints 1K or 2K. It is added by 20-50% depending on the type of finish required. After adding the delustering agent, less thinner (reducer) is required.
Unsaturated polyester resin based on orthophthalic acid and standard glycols, dissolved in styrene. It is pre-accelerated and contains a thixotropic agent. It has a moderate reactivity and low viscosity. It is well suited for manual lamination techniques and projection. During rolling, easily permeates the reinforcing materials and non-sag of the inclined laminates.
Fiberglass chopped strand mat that remain cohesive through an emulsifier 300 g / m2. Especially recommended for the construction of structural composites and laminates for waterproofing parts polyester resins and vinyl ester. It is also widely used for building molds with the same resins. It is not recommended to work with epoxy resins.
Fiberglass chopped strand mat that remain cohesive through an emulsifier 450 g / m2. Especially recommended for the construction of structural composites and laminates for waterproofing parts polyester resins and vinyl ester. It is also widely used for building molds with the same resins. It is not recommended to work with epoxy resins.
The gel coat ISO NEO is a gel coat based on unsaturated polyester resin isophthalic neopentyl glycol. Available in almost all colors of the RAL and NCS. Its specific formula gives this gel, very good mechanical strength and good resistance to hydrolysis and aging outside. The Top Coat version comes paraffin for use as a topping.
Fiberglass mat type of cut yarns that are held together thanks to an emulsifier of 100 g / m2. Especially recommended for the construction of structural laminates for composite parts and waterproofing with polyester and vinyl ester resins. It is also very used for the construction of molds with the same resins. It is not recommended to work with epoxy resins.
Fiberglass mat type of cut yarns that are held together thanks to an emulsifier of 150 g / m2. Especially recommended for the construction of structural laminates for composite parts and waterproofing with polyester and vinyl ester resins. It is also very used for the construction of molds with the same resins. It is not recommended to work with epoxy resins.
High quality grease for lubricating mechanical parts of metal and plastic. It is applied to door hinges, springs, dampers, stabilizers, gums, etc. Prevents wear and galling and resistant against environmental influences, weak acids and bases. Repels water. It Contains Teflon PTFE (politetrafluoreten).
High quality cleaning both inside and outside to carburetors, throttle valves, idle, without dismounting. Solvent has great power and leaves no residue. It is not corrosive. Valve 360 ° C.
High quality brake cleaner with great solvent power. Thanks to its special valve can be applied from any position on drum brakes, disc, brake shoes and brake calipers. It has great solvent power and leaves no residue. It is not conductive or corrosive. 360º valve
Polyurethane Sealant-component medium-high curing with atmospheric moisture module.
The polyurethane foam PRO 45 Pistol is a product of the highest quality recommended for sealing and insulating, filling of cavities, cracks and openings. With a high performance of up to 45 L, excellent acoustic insulation - 62 dB, extraordinary thermal insulation and excellent adhesion to most building materials.
Caliber 30 polyurethane foam gun that increases foam performance by up to 30%. p>
The BUNITEX P-55 contact adhesive is an extraordinarily broad product. It is indicated for the gluing of wood, cork, rubber, synthetic plastic laminates, leather, leather, vegetable or synthetic fibers, some plastics (except polyethylene and other polyolefins) and metals, among themselves or on other types of substrates.
Classic gun PU foam (without HCFC or CFC) is a one-component, ready-to-use polyurethane foam that expands on its own and has added propellant gases that are completely harmless to the ozone layer. With high form stability (no shrinkage or any subsequent expansion), great filling power with excellent application in all materials (except PE or PP), high insulating value, both thermal and acoustic and excellent assembly characteristics.
Polyurethane Foam Cleaner specially developed for effective internal and external cleaning of foam and non-hardened foam guns. Removes all unhardened foam. Internal and external cleaning of the gun
High quality lubricant based on Teflon for the treatment of metal and synthetic parts. High penetration capacity Suitable for use on parts that are under a long or high force and temperature load (-50 ° C to + 250 ° C). Repels water and dirt PTFE offers long-lasting protection against friction and wear. Very good mechanical and thermal stability.
Mixture of clear solvent, suitable for the elimination of fresh spots of glue and the cleaning of brushes, spatulas combs of gluing. Not suitable for polystyrene and plexiglas. It can damage certain media (eg synthetic materials).