Synthetic White Anticorrosive Enamel DTM EX-410 TitanTech

Description

Modified synthetic industrial enamel, with antioxidant additive, fast drying, for direct application on iron or steel. Excellent weather resistance. For any steel surface where a direct application of a single product is desired, in low C2 or medium C3 corrosion environments, according to UNE EN ISO 12944. For structural steel, gates, doors, etc.

Certifications

Reaction to Fire UNE EN 13501-1: B-s1, d0 / on A1 substrate (only valid for maximum thicknesses of 100 dry microns)

Technical characteristics

• Styrene alkyd nature
• Glossy Finish Gloss (UNE EN ISO 2813) 60º:> 85%
• Color (UNE EN ISO 11664-4) Base white 0566
• Density (UNE EN ISO 2811-1) 0.97 - 1.16 Kg / l
• Yield 8 - 12 m² / l (40 - 55 µ)
• Drying at 23ºC 60% RH (UNE 48301) 30 - 60 minutes
• Repainted at 23ºC 60% RH (UNE 48283) Minimum: 30 minutes / Maximum: 4 hours or after 5 days.
• Application Methods Brush (Patch Only), Roller, Spray and Airless
• Gun Dilution: 10 - 15%
• Gun Nozzle Diameter: 1.5mm / Airless: 0.015 "- 0.018"
• Diluent Synthetic Solvent DX 830 or Multipurpose Solvent DX 840
• Cleaning of Utensils Synthetic Solvent DX 830 or Multipurpose Solvent DX 840
• EspRecommended size (UNE EN ISO 2808) 100 - 160 µ dry
• Application Conditions, RH <80% +10 ºC - +30 ºC
• Max volume of dye paste White base: 5%
• Flash point (UNE EN ISO 3679) 27 ºC
• Solid Volume (UNE EN ISO 3233-3) 45 - 47%

* Variations in temperature, humidity, thickness, dyeing or depending on the type of support, etc., may cause changes in drying, performance or other properties

How to use

General recommendations:

Stir well in the container, preferably by mechanical process. Surfaces to be painted must be properly primed, clean, dry and consistent

Unprepared surfaces:

Steel: apply directly DTM EX 410 Anticorrosive Synthetic Enamel, respecting the repainting intervals. If the surface shows rust, sand gently to roughen the substrate, removing poorly adhered rust. The benefits of the scheme are directly related to the preparation of the support. In a C3 corrosion environment, the steel must be sanded to grade ST2 of the UNE EN ISO 8501-1 standard or abrasive blasting to Sa 2 1/2 of the same standard to obtain maximum performance. Non-ferrous metals: apply previously ImprimacAnticorrosive ion Phosphating SX 140 or Acrylic Primer DTM SX 150. In all cases: apply the finishing coats according to the selected scheme (see recommended thickness). Other supports: Consult.

Maintenance of already painted surfaces in good condition:

In case of repainting on well adhered systems, cleaning of grease, oil and dirt (fresh water under pressure, solvent, etc.) and then letting it dry, apply one or two coats of Synthetic Anticorrosive Enamel DTM EX 410, as needed.

Maintenance of already painted surfaces in poor condition:

In the case of poorly adhered systems, and / or with the presence of rust, remove by abrasive blasting to grade Sa2½ of the ISO 8501-1 standard or manual or mechanical cleaning to grade ST3 of the same standard. Directly apply the coats of sufficient DTM EX 410 Anticorrosive Synthetic Enamel, according to requirements.

Precautions

Before using the product, carefully read the instructions on the package. For more information, consult the Safety Data Sheet. Store the containers tightly closed away from sources of heat and temperatures below zero. Shelf life: 36 months in unopened original container. Waste management: Follow the legal provisionslocal ales. Help protect the environment, do not throw waste down the drain, put it in the nearest recycling center. Calculate the amount of product you will need to avoid waste and cost overruns. Keep the excess product well stored for a new use. Paint reuse can effectively minimize environmental effects on the life cycle of products.