TitanTech White Satin Polyurethane Enamel EXB-500 TitanTech

Satin White Polyurethane Enamel EXB-500 TitanTech

22,95VAT included

2-component polyurethane enamel based on an acrylate and an aliphatic isocyanate of great hardness and resistance. With excellent behavior in the open air. Good resistance to yellowing and loss of gloss. Good adhesion on different non-ferrous metals and on certain galvanized.

Size container
Quantity Disponibilidad In stock

You might also like

Related Products ( 11 other products in the same category )

Description

2-component polyurethane enamel based on an acrylate and an aliphatic isocyanate of great hardness and resistance. With excellent behavior in the open air. Good resistance to yellowing and loss of gloss. Good adhesion on different non-ferrous metals and on certain galvanized.

Certifications

Reaction to Fire UNE EN 13501-1: B-s1, d0 / on A1 substrate

Technical characteristics

  • Nature Aliphatic Polyurethane
  • Glossy Satin Finish (UNE EN ISO 2813) 60º: 25 - 35 GU
  • Density (UNE EN ISO 2811-1) 0.96 - 1.25 Kg / l
  • Yield 10 - 12 m² / l (35 - 40 µ)
  • Drying at 23ºC 60% RH (UNE 48301) 2 - 4 hours
  • Repainted at 23ºC 60% RH (UNE 48283) Minimum: 24 hours / Maximum: 7 days
  • Base Mix Ratio: 5 / Hardener: 1
  • Pot Life at 23ºC 4 hours
  • Application Methods Brush, roller, spray gun and airless
  • Brush and Roller Dilution: 0 - 5% / Spray: 10 - 15% / Airless: 0 - 5%
  • Gun Nozzle Diameter: 1.3 - 1.7 mm / Airless: 0.015 "- 0.019"
  • Thinner Epoxy Thinner DX 810 or Polyurethane Thinner DX 820
  • Cleaning of Utensils Epoxy Solvent DX 810 or Polyurethane Solvent DX 820
  • Recommended thickness (UNE EN ISO 2808) 40 - 80 µ dry
  • Application Conditions, HR <80% +10 ºC - + 30 ºC
  • Dyeing System TITANCOLOR Industrial Max volume dye paste White base: 5% / Neutral base. 12.5%
  • Flash point (UNE EN ISO 3679) Base: 26.5 ºC / Hardener: 30.5 ºC
  • Solid Volume (UNE EN ISO 3233-3) Base white: 46 - 48% / Neutral base. 40 - 42% VOC (UNE EN ISO 11890-2) 530 g / l

* Variations in temperature, humidity, thickness, dyeing or depending on the type of support, etc., may cause changes in drying, performance or other properties

How to use

General recommendations:

Stir well in the container, preferably by mechanical process. Surfaces to be painted must be properly primed, clean, dry and consistent. Let the mixture rest for 15 minutes before using it to promote the elimination of air. If the maximum recoating limit is exceeded, to ensure adhesion between coats, a soft blasting (Sand Sweeping) must be carried out, until a slight roughness is conferred on the primed surface.

Unprepared surfaces:

Steel: apply SXB 200 Anticorrosive Epoxy Primer, HB SXB 210 High Thickness Epoxy Primer or HB SXB 220 Rich Epoxy Primer according to specifications, respecting the intervals of repainted. Galvanized: If it does not require certification according to UNE EN ISO 12944, apply directly on properly prepared galvanized steel, eliminating salts and with a slight nuance of the surface. If you require certification, apply SXB 200 Anticorrosive Epoxy Primer or HB SXB 210 High Thickness Epoxy Primer according to the selected scheme. In all cases: apply the finishing coats according to the selected scheme (see recommended thickness). Other supports: Consult.

Maintenance of already painted surfaces in good condition:

In case of repainting on well adhered systems, cleaning of fats, oils and dirt (fresh water under pressure, solvent, etc.) and then letting it dry, apply one or two coats of Polyurethane Multi-surface Satin Enamel EXB 500 according to needs.

Maintenance of already painted surfaces in poor condition:

In the case of poorly adhered systems, and / or with the presence of rust, remove by abrasive blasting to grade Sa2½ of the ISO 8501-1 standard or manual or mechanical cleaning to grade ST3 of the same standard. Next, patch with SXB 200 Anticorrosive Epoxy Primer preferably with a brush and then apply sufficient coats of Satin Multi-surface Polyurethane Enamel EXB 500, according to requirements p>

Precautions

Before using the product, carefully read the instructions on the package. For more information, consult the Safety Data Sheet. Store the containers tightly closed away from sources of heat and temperatures below zero. Shelf life: 36 months in unopened original container. Waste management: Follow local legal provisions. Help protect the environment, do not throw waste down the drain, put it in the nearest recycling center. Calculate the amount of product you will need to avoid waste and cost overruns. Keep the excess product well stored for a new use. Paint reuse can effectively minimize environmental effects on the life cycle of products.

8414800430080

TitanTech https://pinturas-dami.com/img/m/479.jpg

22716
10 Items

Data sheet

Kind of product:
Finishing paint or final coat
Degree of Brightness
Semi-shine
Theoretical yield per hand (m2 / L):
10
Number of recommended hands:
two
Sanding between layers
It is not necessary
Dry to Touch at 23ºC and 60% RH
4 h
Time for repainting at 23ºC and 60% RH
12 h
Diluent / Cleaning:
Polyurethane solvent
Number of Components
2 components
Type Application:
By brush, roller or gun
Place of application
Interior and Exterior
Paint Iron or Steel
Synthetic, Antioxidant or Multipurpose Primer
Paint Aluminum, Brass or Copper
Multipurpose Primer
Paint Wood
Primer Sealer or Multipurpose
Paint Fiber Polyester
Primer Filler
Paint Galvanized Steel
Galvanized or Multipurpose Primer
Paint Already Painted Surfaces
A smooth sanding and painting directly
Danger for transport:
Prohibited Air Transportation

Specific References

ean13
8414800430080

No customer questions for the moment.


Your Question has been successfully sent our team. Thanks for question!
Ask a question
hide form
Captcha

New Account Register

Already have an account?
Log in instead Or Reset password