• -€24.05
Rainbow Paints Brico White Semi-Matte Rainbow Waterproofing Paint 15 L

Brico White Semi-matt Rainbow Waterproofing 15 L

€59.95
35,90VAT included Save €24.05

Plastic-elastic coating based on elastic vinyl copolymers for waterproofing vertical and horizontal surfaces.

Quantity DisponibilidadOut-of-stock

You might also like

Related Products ( 10 other products in the same category )

Description

Plastic-elastic coating based on elastic vinyl copolymers for waterproofing vertical and horizontal surfaces.

Employment: outside

Recommended for waterproofing surfaces not subjected to permanent traffic.

Characteristic

Finish: Semi-Matte

White color

Viscosity: 22,000 +/- 3,000 cps

Density: 1.35 +/- 0.05g/cc

Reaction to fire: Bs1.d0 – UNE 13501-1:2007

Drying: It is highly variable, depending on the temperature and humidity of the environment.

Repainting: 4 hours Total: 20 – 30 days

Theoretical coverage: 1.5 m2 / liter (for 300 microns of dry paint)

Solvent: Water, 10 - 20% first coats without diluting finishing coats

VOC content: Maximum 30 g/l

surface preparation

On all types of support: In the event of contamination by mould, fungus, algae and other parasitic elements, proceed as follows:

1.- Wash with a solution of water and 10% bleach.

2.- Rinse with water.

3.-Let dry completely before starting to paint.

4.- Apply the waterproofing agent diluted at 40% as a primer.

5.- Use products that prevent the formation of mold.

On all types of support:

In case of presence of saline efflorescence (saltpetre): 1.- Brush and wash with a 10% HCl or zinc sulfate solution. 2.- Rinse with water. 3.- Letcar completely before starting to paint. These operations must be carried out observing the corresponding security measures.

On new unpainted supports: On any surface where this paint must be applied, the first thing that is required is a thorough cleaning: rubbing with a hard brush and with a solution of 5% hydrochloric or nitric acid in water, in this way it is ensures perfect cleaning and opens pores. Then clean with water and wait for the surface to dry. When it is clean and dry, a fiber mesh is spread out and fixed by applying a first coat with a mixture containing 60% waterproofing and 40% water. In this way we provide a perfect anchorage to the support. Subsequently, two coats are applied, the first diluted by 15% and the last by 5-10%. Through this procedure, a layer of between 1 and 2 mm is achieved, which would be sufficient to ensure good sealing. These same steps must be extended over the 20 or 30 cm of the surrounding wall, in such a way as to avoid leaks at the joints between terraces and walls due to structural movements of the building.

On painted surfaces: If you are going to paint on previously painted surfaces, make sure that the paint is in good condition. If this is not the case, it must be completely eliminated and proceed as if it were an new unpainted bracket. If the paint is old or poorly adhered with defects such as: chalking, blisters, chipping, cracking..., it must be completely removed before painting and then apply a batch of waterproofing 40% diluted and then two coats, the first diluted at 15% and the second at 5-10%.

Application mode

Brush, roller or spray gun, directly in new construction or by prior preparation of already painted surfaces.

Do not apply on supports whose temperature is below 5ºC, or excessively hot. Similarly, do not apply with a relative humidity higher than 80%, or with strong wind or under risk of rain. Perfectly homogenize the contents of the container. The surfaces to be painted must be clean, dry and completely free of dust and grease. It must be carefully monitored that the surfaces where it is applied are completely dry and do not have leaks. Apply a first coat as a primer of the diluted product in the proportion of three parts of waterproofing with two parts of water. Two coats are then applied, the first diluted with 15% water and the last with 5-10% water. Do not apply when it rains, since when the paint gets wet without being completely dry, its components may dissolve, causing the appearance of spots/glosses (snail slime effect).

Observations

When a m is neededgreater resistance, it is advisable to reinforce the waterproofing with fiber mesh. The surface to be painted must have a 3% slope to avoid watertightness. Flooring is not recommended. Stir the container well before use. Keep the container in a place free of moisture and away from extreme temperature conditions, this should be between approximately 5-35ºC and in a covered place, thus the storage time is 24 months.

Presentation

Lithographed container. Sizes: 4 and 15 litres.

Pinturas Arcoiris https://pinturas-dami.com/img/m/34.jpg

23001

Data sheet

Kind of product:
Finishing paint or final coat
Theoretical yield per hand (m2 / L):
1.5
Number of recommended hands:
two
Dry to Touch at 23ºC and 60% RH
1 hour
Time for repainting at 23ºC and 60% RH
3 h
First layer application
Dilute between 10-15% so that it penetrates well into the support
Diluent / Cleaning:
Water
Type Application:
By brush, roller or gun
Danger for transport:
Innocuous, without restrictions

No customer questions for the moment.


Your Question has been successfully sent our team. Thanks for question!
Ask a question
hide form
Captcha

New Account Register

Already have an account?
Log in instead Or Reset password