Quilosa PU FOAM HAUSER PRO GUN 750 ML QUILOSA

HAUSER PRO PU FOAM GUN 750 ML QUILOSA

7,95VAT included

One-component polyurethane foam that cures in contact with ambient humidity. The foam has been produced in accordance with the ISO 9001:2008 standard.

Quantity Disponibilidad In Stock

You might also like

Related Products ( 12 other products in the same category )

Description

One-component polyurethane foam that cures in contact with ambient humidity. The foam has been produced in accordance with the ISO 9001:2008 standard.

Technical data

  • Capacity (free foam) [l] (RB024) 35 - 41
  • Capacity in a shaft [l] (RB024) 2) 25 - 31
  • Secondary volume increase (subsequent expansion) [%] (TM 1010-2012**) 60 - 90
  • Skin formation time [min] (TM 1014- 2013**) ≤ 10
  • Pre-treatment time [min] (TM 1005-2012**) 3) ≤ 40
  • Full curing time [time] (RB024) 24
  • Thermal conductivity coefficient (λ) [W/mK] (RB024) 0.036
  • Dimensional stability [%] (TM 1004- 2013**) ≤ 5
  • Flammability class (din 4102) B3
  • Flammability class (EN 13501-1:2008) F

Applications

++ FILLING OF VOID SPACES, CRACKS, HOLES, PIPE PENETRATIONS

+ SEALING FOR WINDOW COUPLING

+ SEALING FOR DOOR COUPLING

+ SEALING OF CEILINGS, WALLS AND FLOOR JOINTS

+ THERMAL INSULATION + ACOUSTIC INSULATION

+++ foam indicated/recommended for this use; ++ foam suitable for this use; + foam that meets the basic requirements; - foam not suitable for this use

Properties

■ FOAM CAPACITY

■ FOAM PRESSURE

■ INCREASE IN THE VOLUME OF THE FOAM (SUBSEQUENT EXPANSION)

■ FOAM FLAMMABILITY - MULTIPOSITIONNO FOAM

■ ADHESION

▲▲▲ high; ▲▲ increased; ■ regular; ▼▼ decreased; ▼▼▼ low; - no app

Terms of use

Bottle / applicator temperature [°C] (optimum +20°C) +15 - +30

Substrate / ambient temperature [°C] +5 - +30

How to use

Before application, read the safety instructions given at the end of this Technical Data Sheet and in the Safety Sheet.

1. SURFACE PREPARATION

The foam especially adheres to typical construction materials such as: brick, concrete, plaster, wood, metals, Styrofoam, hard PVC and rigid polyurethane tubing.

• The work surface must be clean and degreased.

• Spray the work surface with water (with a garden sprinkler for example).

• Protect exposed surfaces from possible accidental contamination by applying the foam.

2. PRODUCT PREPARATION

• If a pot is too cold, it will have to be brought to room temperature. For example, immersing it in warm water at a temperature of 30°C or leaving it at room temperature for at least 24 hours.

3. APPLICATION

• Wear protective gloves.

• Shake bottle vigorously (10 - 20 seconds, valve upside down) to thoroughly mix components.

• Screw the bottle onto the applicator.

• The positionThe working order of the boat is “valve upside down”.

• Fill the vertical gaps with foam from bottom to top.

• fill the gap with approximately 1/2 of the volume as the foam expands.

• Gaps greater than 3 cm are not recommended for sealing outdoor carpentry. Gaps greater than 5 cm are unacceptable. Gaps greater than 3 cm must be filled with vertical coats, making sure before applying another coat that the previously applied one has respected the preliminary processing time and that it has been sprayed with water.

• Spray the surface of the applied foam with water (with a garden sprinkler for example).

• If application is interrupted for more than 5 minutes, clean applicator nozzle containing fresh foam with polyurethane foam cleaner and shake can before use.

• In the event that the foam dries up in the applicator, the tip of the applicator should be cut, which would allow you to resume working with the foam.

4. WORKS AFTER COMPLETING THE APPLICATION

• Immediately after complete hardening of the foam, it must be secured against exposure to UV rays using eg plaster or paint.

• If the foam has not been completely spent, the applicator and valve should be cleaned with polyurethane foam cleaner after the job is complete.

5. NOTES / RESTRICTIONS

IT IS FORBIDDEN TO INSTALL DOORS WITHOUT MECHANICAL LINKAGE. LACK OF MECHANICAL COUPLING COULD CAUSE DEFORMATION OF THE INSTALLED ELEMENT.

  • The curing process depends on temperature and humidity. Decreasing the ambient temperature for 24 h after application below the minimum application temperature may affect the quality and/or accuracy of the joint.
  • Hasty attempts at preliminary treatment can cause irreversible changes in the foam structure and its stability as well as affect the deterioration of the foam's utility parameters.
  • The foam does not adhere to polyethylene, polypropylene, polyamide, silicone or Teflon.
  • Remove fresh foam with polyurethane foam cleaner.
  • Cured foam may only be removed mechanically (eg with a knife).
  • The quality and technical conditions of the applicator used will influence the parameters of the final product.
  • Do not use the foam in spaces where there is no fresh air or poor ventilation or in places exposed to direct sunlight.
  • The manufacturer recommends using the entire contents of the container a single strip of foam (at one time), because in the event that the foam dries up in the applicator, it would not be possible to reuse it.
*If you want more information about this productOr, you can download your technical sheet in the "ATTACHMENTS" tab

Quilosa https://pinturas-dami.com/img/m/14.jpg

23037
12 Items

Data sheet

Kind of product:
Polyurethane foam
Dry to Touch at 23ºC and 60% RH
10 minutes
Type Application:
PU foam gun
Danger for transport:
Prohibited Air Transportation
Capacity (free foam)
Up to 45 (L)
Capacity in a hole
22 - 28 (L)
Increase in secondary volume (subsequent expansion) [%]
180 - 210 (%)
Acoustic isolation
62dB

No customer questions for the moment.


Your Question has been successfully sent our team. Thanks for question!
Ask a question
hide form
Captcha

New Account Register

Already have an account?
Log in instead Or Reset password