Quilosa Polyurethane foam ORBAFOAM B1 FIRE STOP Gun 750 ML Quilosa

ORBAFOAM B1 FIRE STOP polyurethane foam Gun 750 ML Quilosa

15,95VAT included

One-component polyurethane foam that cures in contact with ambient humidity. The foam has been produced in accordance with the ISO 9001:2015 standard.

Quantity Disponibilidad In Stock

You might also like

Related Products ( 11 other products in the same category )

Description

One-component polyurethane foam that cures in contact with ambient humidity. The foam has been produced in accordance with the ISO 9001:2015 standard.

Technical data

  • Gray

Parameter (+23°C/50% RH) 1)

  • Capacity (free foam) [l] (RB024) 35- 42
  • Capacity in a shaft [l] (RB024) 2) 24 - 32
  • Secondary volume increase (subsequent expansion) [%] (TM 1010-2012**) 90 - 120
  • Skin formation time [min] (TM 1014-2013**) ≤ 10
  • Pre-treatment time [min] (TM 1005-2012**) 3) ≤ 40
  • Full curing time [time] (RB024) 24
  • Thermal conductivity coefficient (λ) [W/mK] (RB024) 0.036
  • Dimensional stability [%] (TM 1004- 2013**) ≤ 3
  • Flammability class (din 4102) B1
  • Flammability class (EN 13501- 1+A1:2010) test method EN ISO 11925-2, EN 13823 Bs1d0
  • Fire resistance (EN 13501-2+A1:2008) test method EN 1366-4:2008: El240

Applications

++ SEALING FOR WINDOW COUPLING

+ SEALING FOR DOOR COUPLING

+ FILLING OF EMPTY SPACES, CRACKS, HOLES, PIPE PENETRATIONS

+ SEALING OF CEILINGS, WALLS AND FLOOR JOINTS

+ THERMAL INSULATION

+ SOUND INSULATION

+++ foam indicated/recommended for this use; ++ foam suitable for this use; + foam that meets the basic requirements; - foam not suitable for this use

Properties

▼▼▼ B1/Bs1d0 FLAMMABILITY OF FOAM

▲▲▲ EI240 LINEAR FIRE RESISTANCE CONNECTOR

■ FOAM CAPACITY

■ FOAM PRESSURE

■ INCREASED FOAM VOLUME (BACK EXPANSION) - MULTI-POSITION FOAM

■ ADHESION OF THE FOAM TO THE SURFACE

▲▲▲ high; ▲▲ increased; ■ regular; ▼▼ decreased; ▼▼▼ low; - no app

Terms of use

Bottle / applicator temperature [°C] (optimum +20°C) +10 - +30

Substrate / ambient temperature [°C] +10 - +30

How to use

Before application, read the safety instructions given at the end of this Technical Data Sheet and in the Safety Sheet.

1. SURFACE PREPARATION

The foam especially adheres to typical construction materials such as: brick, concrete, plaster, wood, metals, Styrofoam, hard PVC and rigid polyurethane tubing.

• The work surface must be clean and degreased.

• The surface can be sprayed with water at an application temperature above 0°C.

2. PRODUCT PREPARATION

• If a pot is too cold, it will have to be brought to room temperature. For example, immersing it in warm water at a temperature of 30°C or leaving it at room temperature for at least 24 hours.

• The applicator temperature cannot be lower than the tempot perature.

3. APPLICATION

• Wear protective gloves.

• Shake bottle vigorously (10 - 20 seconds, valve upside down) to thoroughly mix components.

• Screw the bottle onto the applicator.

• The working position of the boat is “valve upside down”.

• Fill the vertical gaps with foam from bottom to top.

• Do not fill the gap completely - the foam will increase in volume.

• Gaps greater than 3 cm are not recommended for sealing outdoor carpentry. Gaps greater than 5 cm are unacceptable. Gaps greater than 3 cm must be filled with vertical coats, making sure before applying another coat that the previously applied one has respected the preliminary processing time and that it has been sprayed with water.

• If application is interrupted for more than 5 minutes, clean applicator nozzle containing fresh foam with polyurethane foam cleaner and shake can before use.

4. WORKS AFTER COMPLETING THE APPLICATION

• Immediately after complete hardening of the foam, it must be secured against exposure to UV rays using eg plaster or paint.

• After finishing work, thoroughly clean the applicator. To do this, screw a bottle of cleaner onto the applicator and squeeze the trigger until the liquid begins to come out

5. NOTES / RESTRICTIONS

IT IS FORBIDDEN TO INSTALL DOORS WITHOUT MECHANICAL LINKAGE. LACK OF MECHANICAL COUPLING COULD CAUSE DEFORMATION OF THE INSTALLED ELEMENT.

  • The curing process depends on temperature and humidity. Decreasing the ambient temperature for 24 h after application below the minimum application temperature may affect the quality and/or accuracy of the joint.
  • Hasty attempts at preliminary treatment can cause irreversible changes in the foam structure and its stability as well as affect the deterioration of the foam's utility parameters.
  • The foam does not adhere to polyethylene, polypropylene, polyamide, silicone or Teflon.
  • Remove fresh foam with polyurethane foam cleaner.
  • Cured foam may only be removed mechanically (eg with a knife).
  • The quality and technical conditions of the applicator used will influence the parameters of the final product.
  • Do not use the foam in spaces where there is no fresh air or poor ventilation or in places exposed to direct sunlight.
  • The manufacturer recommends using the entire contents of the container a single strip of foam (at one time), because in the event that the foam dries up in the applicator, it would not be possible to reuse it.
*If you want more information aboute this product, you can download its technical sheet in the "ATTACHMENTS" tab

Quilosa https://pinturas-dami.com/img/m/14.jpg

23040
9 Items

Data sheet

Kind of product:
Polyurethane foam
Dry to Touch at 23ºC and 60% RH
10 minutes
Type Application:
PU foam gun
Danger for transport:
Prohibited Air Transportation
Capacity (free foam)
Up to 45 (L)
Capacity in a hole
24 - 32L
Increase in secondary volume (subsequent expansion) [%]
180 - 210 (%)
Full curing time
5 min

No customer questions for the moment.


Your Question has been successfully sent our team. Thanks for question!
Ask a question
hide form
Captcha

New Account Register

Already have an account?
Log in instead Or Reset password