Water Pools Titan 4 L
Special matte painting water to cement or concrete pools easy to apply and quick drying. The paint film is highly resistant to the formation of algae.
You might also like
Related Products ( 4 other products in the same category )
Description
Special matte painting water to cement or concrete pools easy to apply and quick drying. The paint film is highly resistant to the formation of algae.
Features
- Effect Antialgas
- Slip
- Long-Term
- Matte finish
- Ease of Application
- Odor Mild
- Recoatable on chlorinated rubber paint
Technical characteristics
- Nature: Acrylic
- Matte finish
- Color: White & Blue
- Yield: 8 to 12 m² / Lt
- Drying at 23 ° C and 60% RH: 30 minutes
- Repainting at 23 ° C and 60% RH: 6 hours
- Method of application: roller and brush
- Dilution: water (10%)
- Cleaning of tools: Water
- Layers: 2 layers in new construction and maintenance of one layer and painted pools
How to use
General recommendations:Stir in the package. The surfaces must be clean, dry and consistent, cement should be set. To fill the pool after painting, wait 7 or 8 days. Painted with water based paints pools should not be repainted with other chlorinated rubber based or strong solvents.
Submerged or not, they must first prepare metal surfaces. The results painted a swimming pool depends on the construction and location of it. The growth of algae in the water depends on the correct debug it.
Unprepared surfaces:
-New concrete pools Em>After not paint built before at least 2 months. Treating the surface with a mixture of 1 part hydrochloric acid (Salfuman) and 3 - 4 parts water. Rinse with fresh water under pressure. Allow to dry thoroughly for at least 48 hours and apply a coat diluted with 10% water; once dry, apply one or two coats undiluted TITAN Water Pools.
- Piscinas old unpainted:Wash with a mixture of 1 Kg of trisodium phosphate with 10 liters of water or a detergent solution powder 5% water by removing molds and fats using a brush esparto.; rinse with fresh water pressure and proceed as in new pools.
Painted surfaces in good condition:Remove debris with trisodium phosphate, according to the procedure outlined in paragraph Pools old unpainted and apply 1 or 2 coats of TITAN Water Pools undiluted.
Painted surfaces in poor condition:Remove the paint in poor condition. If the damaged area is large remove the paint by sandblasting. Then wash with trisodium phosphate or a solution of detergent powder 5% in water, rinsing thoroughly with clean water and proceed as in new pools. When you can not remove all the paint by sandblasting or stung, apply a general primer Epoxy Corrosion yacht TITAN to seal and equalize takeovers. After 24 hours, apply 1 or 2 coats of TITAN Water Pools.
Data sheet
- Kind of product:
- Finishing paint or final coat
- Degree of Brightness
- Mate
- Theoretical yield per hand (m2 / L):
- 8
- Number of recommended hands:
- two
- Sanding between layers
- It is not necessary
- Dry to Touch at 23ºC and 60% RH
- 30 min
- Time for repainting at 23ºC and 60% RH
- 6 a.m.
- First layer application
- Dilute between 10-15% so that it penetrates well into the support
- Time for maximum hardness
- 7 days
- Diluent / Cleaning:
- Water
- Type Application:
- With brush or roller
- Place of application
- Only Exterior
- Paint Fiber Polyester
- Prohibited
- Paint Concrete or Cement
- Directly
- Paint Already Painted Surfaces
- Directly without sanding
- Danger for transport:
- Innocuous, without restrictions
- advice
- Do not repaint this paint with chlorinated rubber paint
Specific References
- ean13
- 8414800032321
No customer questions for the moment.