Titan Pro Anti-leakage coating I5 Titan Pro

Anti-tip coating I5 Titan Pro

8,45VAT included

Coating for roof waterproofing, easy to apply. Repair of areas with cracks or with tendency to form. Can be walked or walked on without continuity except heavy traffic. It adapts and adheres on the materials used in construction, obtaining a waterproof barrier. With anti-mold preservative and antiverdin. Resistant to alkalis, such as cement. Up to 5 years warranty upon request and prescription.

Size container
Colour
Selected color: English Red
Quantity Disponibilidad In stock

Related Products ( 10 other products in the same category )

Description

Coating for roof waterproofing, easy to apply. Repair of areas with cracks or with tendency to form. Can be walked or walked on without continuity except heavy traffic. It adapts and adheres on the materials used in construction, obtaining a waterproof barrier. With anti-mold preservative and antiverdin. Resistant to alkalis, such as cement. Up to 5 years warranty upon request and prescription.

Technical data

  • Nature: Modified Acrylic
  • Finish: Semi-matt
  • Color (UNE EN ISO 11664-4): White and range colors
  • Density (UNE EN ISO 2811-1): 1.28 - 1.33kg / l
  • Performance (UNE 48282): 0.6 - 0.7 m² / l (approximately 1.5 l / m²)
  • Drying at 23ºC 60% RH (UNE 48301): 6 - 8 hours
  • Repaint at 23ºC 60% RH (UNE 48283): 18 - 24 hours. Pisable: 2 - 3 days
  • Application Methods: Brush and roller
  • Thinner: Water
  • Recommended thickness (UNE EN ISO 2808): 1.0 - 1.2 mm dry film
  • Application Conditions, HR 80% + 10ºC - +30ºC
  • Solid Volume (UNE EN ISO 3233-3): 40.5 - 41.5%
  • VOC (UNE EN ISO 11890-2) 2.004 / 42IIA (c) (75/40) Max. VOCs 5 g / l.

* Variations of temperature, humidity, thickness, dyeing or type of support, etc., can cause changes in drying, performance or other properties.

Certifications

Determination of tensile strength and elongationbreakage UNE-EN ISO1798: 2001: Tensile strength: ơ: 0.98MPa / Elongation at break ɛ: 665%

How to use

GENERAL RECOMMENDATIONS:

Stir well in the container. The surfaces to be painted must be clean, dry and consistent.

VERY IMPORTANT ATTENTION. DO NOT APPLY: At temperatures below 7º C. With relative humidity greater than or equal to 80%. With forecast of rain in the next hours. If these instructions are not respected, the result of the application may not be satisfactory. Industrias TITAN, SAU will not accept any claim that has not taken into account these instructions. If there are cracks greater than 1 m / m, it is advisable to cover them beforehand, and / or reinforce them with mesh tape placed between the layers of the I5 Antigoteras coating that is applied.

To ensure the tightness of horizontal terraces, it is advisable to follow the application of the I5 Antigotera coating, up to a certain height of the vertical walls, reinforcing if necessary the angle of union of the two surfaces. To guarantee the result, place between the layers of the I5 Antigoteras coating, a continuous fiber reinforcement throughout the surface, this improvement increases the thickness and the resistance being convenient in areas that are stepped with more frequency. While the paint is not dry thoroughly, it is sensitive to water.

SUPPERFICIES NOT PREPARED:

Clean, removing loose debris, smoothing and levelingthe slopes or unevenness of the surface to be painted, to avoid possible puddles. Apply the first layer diluted with 25% water and the second one as such to the indicated yields. It is important to apply a thickness of 1 -1,2 mm., To achieve an elasticity that allows to maintain the continuity of the film without breaking, in the event that new cracks are formed in the protected surface.

MAINTENANCE OF PAINTED SURFACES IN GOOD CONDITION:

Directly apply the previously washed or brushed paint, diluting the first layer with 25% water, then apply the second layer as is p>

MAINTENANCE OF ALREADY PAINTED SURFACES IN BAD CONDITION:

Completely remove the old paints and proceed as on unprepared surfaces.

8414800413021

Titan Pro https://pinturas-dami.com/img/m/69.jpg

21697
24 Items

Data sheet

Kind of product:
Finishing paint or final coat
Degree of Brightness
Semi-matt
Theoretical yield per hand (m2 / L):
3
Dry to Touch at 23ºC and 60% RH
6 - 8 a.m.
Time for repainting at 23ºC and 60% RH
18-24h
Diluent / Cleaning:
Water

Specific References

ean13
8414800413021

Download

FT Revest. antigot Titan Pro

FT Anti-tip coating I5 Titan Pro

Download (152.87k)

No customer questions for the moment.


Your Question has been successfully sent our team. Thanks for question!
Ask a question
hide form
Captcha

New Account Register

Already have an account?
Log in instead Or Reset password