Oxirite Xtrem Bright Water
antioxidant water enamel applied directly on metal without priming in different colors. It incorporates special raw materials as a hydrophobic acrylic resin which gives a high resistance to corrosion, moisture and water as well as excellent adhesion on different media.
You might also like
Related Products ( 16 other products in the same category )
Product Description
antioxidant water enamel applied directly on metal without priming in different colors. It incorporates special raw materials as a hydrophobic acrylic resin which gives a high resistance to corrosion, moisture and water as well as excellent adhesion on different media. For formulation they have been chosen highly effective anti-corrosion additives, non-hazardous and free of heavy metals.
Features antirust paint Oxirite
- Direct application on metal, unprimed.
- It can be applied on rusty surfaces, previously removing loose particles. Li>
- Glossy finish.
- Good adhesion on different surfaces.
- Fast drying. Li>
- Easy to apply. Li>
- Weak odor that disappears when dry. Li>
- waterbased
Performance
In urban and industrial atmospheres, moderate sulfur dioxide pollution and coastal areas with low salinity con 80 dry microns will suffice (about 5 m² / L). For more aggressive environments need to be applied above 100 microns dry (about 4 m² / L). According to tests performed in the Laboratory of Tecnalia according to ISO 12944, with 80 dry microns, Oxirite Xtrem meets the criteria for atmospheric environments C3-C4 medium low.
Preparation of surfaces
Apply on clean, free of oil and grease and dry surfaces. They are painted with dirt surfaces should be washed with water, detergent and brush, soap deslavando well in the end. This process can be done with pressurized water. Remove non-adhering coatings, pickling, scraping or sanding.
In the case of metal sheets with fats and oils, they must be completely eliminated by using alkaline detergents (for aluminum surfaces should be neutral) or appropriate solvents. Surfaces must completely degreased to ensure good adhesion and corrosion maximum efficiency.
Using a hammer or chisel crusts of rust, scale and welding slag or dross clinging to rusty iron elements removed. If the surface also has areas of corrosion, it should scratch it with a wire brush or abrasive emery to Knockar all loose rust and scale. St-2 level (UNE-EN-ISO 12944- 4).
To remove dust particles that may have surface before painting, you can be cleaned with a brush or bristle brush. They can do this work also applying to the surface a jet of clean, dry air. In the case of boards and electric instruments and pneumatic vacuum cleaner will be used.
Surfaces painted with oil glazes that have not been exposed to the weather is suitable sand the surface to improve adhesion.
When masking tapes (tapes coachbuilders) are used, they must come off before the paint has finished drying (30-60 min). If the paint has already dried and has formed a consistent film with the tape, the tape must be removed by cutting the edges with a knife.
It is not necessary to apply a corrosion or adherent primer.
Apply the product undiluted.
For good antioxidant protection, apply at least two coats.
drying
Surface drying normally at least 1 hour. Repainting: 2 to 3 hours depending on the environmental conditions. The painting adquiere maximum hardness after a week of being applied.
application
Apply the product undiluted. Remove from the bottom up until a homogeneous color. The color will be reached once the product is dry. For good antioxidant protection, apply at least two coats. The product can be applied by brush, brush, roller gun and short hair.
Notice
The colors are approximate and may vary depending on the computer screen you are using.
Data sheet
- Kind of product:
- Antioxidant finish without primer
- Degree of Brightness
- Brightness
- Theoretical yield per hand (m2 / L):
- 10
- Number of recommended hands:
- two
- Sanding between layers
- It is not necessary
- Dry to Touch at 23ºC and 60% RH
- 1 hour
- Time for repainting at 23ºC and 60% RH
- 2 hours
- Time for maximum hardness
- 7 days
- Diluent / Cleaning:
- Water
- Number of Components
- 1 component
- Type Application:
- By brush, roller or gun
- Place of application
- Interior and Exterior
- Paint Iron or Steel
- Directly
- Paint Aluminum, Brass or Copper
- Directly
- Paint Wood
- Directly
- Paint Galvanized Steel
- Directly
- Paint Already Painted Surfaces
- A smooth sanding and painting directly
- Danger for transport:
- Innocuous, without restrictions
Specific References
- ean13
- 8414956717172
No customer questions for the moment.