HP White Gloss Polyurethane Enamel Base EXB-550 TitanTech

Description

Glossy two-component polyurethane enamel formulated based on an aliphatic isocyanate and a polyacrylate with a high degree of crosslinking.

Certifications

Two-component aliphatic polyurethane paint with a glossy finish UNE 48274: Complies with Reaction to Fire UNE EN 13501-1: B-s1,d0/on A1 substrate

Characteristics

- Excellent weather resistance in corrosive industrial and marine environments.

- High chemical resistance.

- Excellent color and gloss retention in environments with high C4 or very high C5 corrosion, according to UNE EN ISO 12944.

- For steel structures previously primed with recommended two-component epoxy primers.

Technical characteristics

• Nature High performance aliphatic polyurethane
• Glossy Glossy Finish (UNE EN ISO 2813) 60º: > 85 GU
• Color (UNE EN ISO 11664-4) White base 0566 and Neutral base 0597
• Density (UNE EN ISO 2811-1) 1.00 - 1.22 Kg/l
• Coverage 10 - 12 m²/l 45 - 55 µ)
• Drying at 23ºC 60% HR (UNE 48301) 4 - 5 hours
• Repainting at 23ºC 60% RH (UNE 48283) Minimum: 24 hours / Maximum: 5 days
• Base Mix Ratio: 4 / Hardener: 1
• Pot life at 23ºC 5 hours
• Application Methods Brush, roller, spray and airless
• Dilution Brush: 5% / Roller 0 - 5% / Gun: 15 - 25% / Airless: 0- 5%
• Gun Nozzle Diameter: 1.7 mm / Airless: 0.015"- 0.019"
• Thinner Epoxy Thinner DX 810 or Polyurethane Thinner DX 820
• Cleaning of Utensils Epoxy Solvent DX 810 or Polyurethane Solvent DX 820
• Recommended Thickness (UNE EN ISO 2808) 40 - 80 µ dry
• Application Conditions, RH<80% +10 ºC - +30 ºC
• Dyeing Industrial TITANCOLOR System
• Vol.max coloring paste White base: 5% / Neutral base: 12.5%
• Flash point (UNE EN ISO 3679) Base: 35 ºC Hardener: 33 ºC
• Solid Volume (UNE EN ISO 3233-3) 49 - 52 % VOC (UNE EN ISO 11890-2) 480 g/l
• *Variations in temperature, humidity, thickness, dyeing or depending on the type of support, etc., can cause changes in drying, performance or other properties

How to use

General recommendations:

Stir well in the container, preferably by mechanical process. The surfaces to be painted must be properly primed, clean, dry and consistent. Let the mixture rest for 15 minutes before using it to favor the elimination of air. In case of exceeding the maximum limit of repainting, to ensure the adhesion between layers, a soft sandblasting must be carried out, until conferring aslight roughness to the primed surface

Unprepared surfaces:

Steel: apply SXB 200 Anticorrosive Epoxy Primer, HB SXB 210 High Thickness Epoxy Primer or HB SXB 220 Zinc Rich Epoxy Primer according to specifications, respecting the repainting intervals. Galvanized: If certification according to UNE EN ISO 12944 is not required, apply directly on suitably prepared galvanized steel, eliminating salts and lightly shading the surface. If certification is required, apply SXB 200 Anticorrosive Epoxy Primer or HB SXB 210 High Thickness Epoxy Primer according to the selected scheme. In all cases: apply the finishing coats according to the selected scheme (see recommended thickness). Other supports: Consult.

Maintenance of already painted surfaces in good condition:

If repainting on well-adhered systems, clean from grease, oil and dirt (pressurized fresh water, solvent, etc.) and then let it dry, apply one or two layers of EXB 500 Satin Multi-Surface Polyurethane Enamel as needed.

Maintenance of already painted surfaces in poor condition:

In the case of poorly adhered systems, and/orIn the presence of rust, remove by abrasive blasting to the Sa2½ degree of the ISO 8501-1 standard or manual or mechanical cleaning to the ST3 degree of the same standard. Then patch with SXB 200 Anticorrosive Epoxy Primer preferably by brush and then apply enough coats of EXB 500 Satin Multi-Surface Polyurethane Enamel, according to requirements

Precautions

Before using the product, read the package instructions carefully. For more information consult the Safety Data Sheet. Store tightly closed containers away from sources of heat and temperatures below zero. Conservation: 36 months in original unopened container. Waste management: Follow local legal provisions. Help protect the environment, do not throw waste down the drain, deposit it at the nearest recycling center. Calculate the amount of product you will need and thus avoid waste and extra cost. Keep the leftover product well stored for a new use. Paint reuse can effectively minimize environmental effects on the life cycle of products.