Polyurethane varnish + satin acrylic Titan yacht
Two component varnish satin, formulated with acrylic polyol with high degree of crosslinking and aliphatic isocyanate with ultraviolet filters. Resistant to chemical agents, fats, gasoline, gas-oil, etc., especially in marine environments. Great hardness and elasticity Retention of brightness. Very resistant to wear and wash. It does not yellow.
You might also like
Related Products ( 3 other products in the same category )
Description h3>
Two component varnish satin, formulated with acrylic polyol with high degree of crosslinking and aliphatic isocyanate with ultraviolet filters. Resistant to chemical agents, fats, gasoline, gas-oil, etc., especially in marine environments. Great hardness and elasticity Retention of brightness. Very resistant to wear and wash. It does not yellow.
Technical data h3>
- Nature: Acrylic polyol catalyzed with aliphatic isocyanate
- Finish: Satin li>
- Color (UNE EN ISO 11664-4): Colorless li>
- Density (UNE EN ISO 2811-1): 1.00 - 1.02 Kg / l li>
- Performance (UNE 48282): 14 - 16 m2 / l li>
- Drying at 23ºC 60% RH (UNE 48301): 3 - 4 hours
- Repainted at 23ºC 60% RH (UNE 48283): 12 - 24 hours
- Proportion of Base Mix: 4 / Hardener: 1 li>
- Life of the mixture at 23ºC: 4 - 8 hours
- Application Methods: Air gun, roller, brush Dilution Air gun: 10 - 20% / Roller and Brush 3 - 5%
- Diluent: Diluent TITAN Yacht li>
- Utensils Cleaning: TITAN Diluent Yacht li>
- Recommended thickness (UNE EN ISO 2808): 80 ?? li>
- Flash Point (UNE EN ISO 3679): 35 ºC
- Solid Volume (UNE EN ISO 3233-3): 45 - 47%
* Variations of temperature, humidity, thickness or type of support, etc., can cause changes in drying, yield, etc. p>
Modeof employment
GENERAL RECOMMENDATIONS:
The surface must be sanded, clean, dry and free of salt (wash it). Do not varnish in full sun, nor with dew. 2 Hardwoods (Teak, Iroco, Tropical Woods, etc.) and resinous woods (Melis, pine, etc.): Thoroughly washed with TITAN Yacht Diluent (to remove the resin). Dilute the first layer with 10% TITAN Yate Diluent. Wait 24 hours to observe possible resin oozing and drying delay of the varnish. If it occurs, proceed to wash again with TITAN Yacht Diluent. Sand between layer and layer. Finish with 2 - 3 coats of Polyurethane Varnish + Acrylic TITAN Yacht, as is.
SURFACES NOT PREPARED:
Dilute the first layer with 20 - 30% of TITAN Yate Diluent. Sand between layer and layer. Finish with 2 - 3 coats of Polyurethane Varnish + Acrylic TITAN Yacht p>
MAINTENANCE OF PAINTED SURFACES IN GOOD CONDITION:
Completely remove cracked or detached varnish. Sand the old varnish well adhered until shading; and apply 2 - 3 coats of Polyurethane Varnish + Acrylic TITAN Yacht, as is. p>
MAINTENANCE OF PAINTED SURFACES IN POOR CONDITION:
Remove the coating in poor condition until a solid wood surface is obtained through sandpaper, brush or TITAN Plus Paint remover and proceed as in unprepared surfaces p>
* If you want more information about this product, you can download its technical sheet in the tab "ATTACHMENTS"
Data sheet
- Kind of product:
- Finishing paint or final coat
- Degree of Brightness
- Satin
- Theoretical yield per hand (m2 / L):
- 14
- Number of recommended hands:
- two
- Sanding between layers
- It is not necessary
- Dry to Touch at 23ºC and 60% RH
- 6 - 7 h
- Time for repainting at 23ºC and 60% RH
- 24 h
- Diluent / Cleaning:
- Specific Solvent
- Number of Components
- 2 components
- Type Application:
- With brush or roller
- Place of application
- Interior and Exterior
- Paint Wood
- Tapaporos Fund
- Paint Already Painted Surfaces
- A smooth sanding and painting directly
- Danger for transport:
- Prohibited Air Transportation
No customer questions for the moment.